Whats the difference?

[KB93z28]

Ok, so Ive been wondering this for a long time, you see parts for 93 camaros only and then you see parts for 94 and 95 camaros only. Whats the difference between the 93 LT1s and the 94 LT1s? I know one difference is that my car (a 1993) does not have a MAF.

[Formula413]

A '93 has a totally different computer. It has an engine control module (ECM) to run the engine that actually uses a chip, so tuning is done by burning different chips. '94 and up use a powertrain control module (PCM) which controls both the engine and transmission and does not use chips, but rather is reflashed for tuning. The transmissions are different as well, if it's an auto it's a 4L60 as opposed to a 4L60E (electronically controlled via PCM), and if it's a 6 speed it has a lower first gear ratio and a different rear axle ratio (2.73 or 3.23, as opposed to 3.42 for '94 and up 6 speeds). Also as you noted the '93 has no MAF sensor and uses a speed density tune. I believe the injectors are smaller on a '93 as well. Pizza knows all this stuff, I'm sure he will chime in.

[KB93z28]

So would a bone stock 1993 camaro be slower than a bone stock 94 camaro?

[Batman]

Not necessarily, just different. You can bet the 94 is more efficient though

[KB93z28]

I remember reading somewhere that it was said that the '93 had a slightly bigger cam, now I dont know how much truth there is behind that, personally I dont think its true lol

[Formula413]

Originally Posted by KB93z28

I remember reading somewhere that it was said that the '93 had a slightly bigger cam, now I dont know how much truth there is behind that, personally I dont think its true lol

No, the cam was the same 93-95, and only a tiny bit different from 96-97. 93-95 are all rated at 275 hp stock, it's not likely that a '93 would be significantly faster or slower than a 94-95.

[irockidz28]

i beleive pizza said there was some sort of difference with the fuel rails on the intake?? maybe

[941LE]

ya the intakes r different. 93s didnt have the cross over tube in the front like the 94-97s do.

[ILuvPizzaTimes10]

Originally Posted by Formula413

No, the cam was the same 93-95, and only a tiny bit different from 96-97. 93-95 are all rated at 275 hp stock, it's not likely that a '93 would be significantly faster or slower than a 94-95.

incorrect. cams are different. ive never been able to track down an Actual Spec on the cam BUT they are different numbers from the GM Book. 93 had 19lb injectors. 94+ has 24. exhaust manifolds are COMPLETLY different. smog pump is mounted on the block 1993 and on the frame rail 94+. cylinder heads as well are different casting numbers that flow the best(debatable) but aren't as portable friendly. Intake is again different as the guys covered, But as i recently found out(suicidal racing) they are better for porting. the front suspension has SLIGHT differences. most aftermarket parts will fit But the geometery gets wierd on the alignment rack. i think its the over all height of the knuckle. 94+ is shorter. by fractions of an inch. the 93 offered 2 ratio choices in the T56. if you had a 2.73 rear ratio the first gear of the 6 speed was 3.07. if you had a 3.23 as i did stock the first gear was the Sought after 2.97 ratio. can i go on? or did i cover the basics? Ohh and the valve springs and retainers are different. Almost all of this is the same for 92-93 vette as well. PM me if you wanna know more.

[Formula413]

Factory LTX Camshaft Specifications:
1992 Y-body: 205/207 0.451/0.450 lift 117 LSA
1993-1995 Y-body, F-body: 202/207 0.450/0.460 lift 116 LSA
1994-1996 B-bodies (including L99 4.3L): 191/196 0.418/0.430 lift 111 LSA
1996 Y-body, 1996-1997 F-body: 200/207 0.447/0.459 lift 117 LSA
1996 Y-body, F-body LT4: 203/210 0.476/0.479 lift 115 LSA

.