North East F-Body Association

North East F-Body Association (http://www.northeastf-bodyassn.com/index.php)
-   Fourth Generation (http://www.northeastf-bodyassn.com/forumdisplay.php?f=16)
-   -   Need to replace my A/C compressor (http://www.northeastf-bodyassn.com/showthread.php?t=1575)

Formula413 08-11-2010 02:11 AM

Need to replace my A/C compressor
 
Has anyone ever replaced an A/C compressor on an LT1? Mine is leaking, just want to know how difficult it is before I dive into it.

irockidz28 08-11-2010 02:20 AM

i did one on a TPI like 4 days ago took like 10 mins but i have way more room then you do but i f*cked mine up now it wont turn on and the blower fan doesnt work idk what i did but good luck with it lol

Greenbird94ta 08-11-2010 02:59 AM

it's kinda a pain in the dick, you have to take the acc. bracket off, to get to it, then u have to get the back bolts off that bolt the lines to the back of the compressor as well, and that bolt sucks. good luck man. mine was all fucked up so i ended up cutting it off lol

ILuvPizzaTimes10 08-11-2010 02:23 PM

I won't say there easy but there not super tough. You don't need to remove the acc bracket if you have access to a lift and the back bolts are easiest to get to by renoving the starter and going in from the backside. Good luck. LT1=Fail

Formula413 08-11-2010 11:34 PM

I'll almost certainly be doing it without a lift, so if I need to pull the accessory bracket so be it. Also, my Haynes manual says you hafta replace the receiver/dryer at the same time, is that absolutely necessary, even if I'm just putting in a used compressor?

ILuvPizzaTimes10 08-12-2010 02:29 AM

Why is the compressor bad? If its internal and sendind metal threw the system the reciever dryer is what will hold that metal and kill the new/used compressor id change it for sure!

Formula413 08-12-2010 02:41 AM

The only thing wrong with the compressor is that it's leaking. If I recharge the system the A/C blows cold again until the refrigerant leaks out again. So I have no reason to suspect internal damage.

ILuvPizzaTimes10 08-12-2010 03:15 AM

Everytime you refill it are you using oil. And if so do you vac out the old and filling it with the proper amount of oil each time? If you aren't doing all of the above on every fill you are most certainly hurting the compressor. Wich in turn will leave fillings and build up behind. Would you change the oil in your car and leave the old oil filter in the car?

KLAB 08-12-2010 04:39 AM

Alex all you need is time and tools. I did mine in 2008 when I got the car with the nose about a foot or a lil more off the ground and laying in the dirt. I'd say just go in there and start loosening up all the shit around it to make it easier. I just started taking things off and then I was like "oooooooh sooo thats where the bolts are...." Mine was seized up so I got a new one. Hell yes for A/C <3 :klab:

941LE 08-12-2010 12:10 PM

take the tops off. problem fixed

Formula413 08-12-2010 12:39 PM

Quote:

Originally Posted by 941LE (Post 26999)
take the tops off. problem fixed

Doesn't work so good if there's a downpour.

941LE 08-12-2010 01:26 PM

then u should b driving the civic at that time lol

KLAB 08-12-2010 04:58 PM

Yeah if I had t-tops I'd honestly prob go for the A/C delete myself. But us badass people with hardtops need A/C, well at least I do... lol

MTX 08-12-2010 05:11 PM

yeah tpi ones are easy and mine took a shit going thru Georgia coming up here.

Formula413 08-12-2010 08:26 PM

To each his own, but my A/C is staying, so back on topic.

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 26971)
Everytime you refill it are you using oil. And if so do you vac out the old and filling it with the proper amount of oil each time?

The refrigerant I've recharged it with has oil in it, so I should be good there. I'm pretty sure all the refrigerant they sell at parts stores actually has oil in it.

BrokenFeather78 08-12-2010 11:40 PM

Even if your compressor hasn't shot chunks into the dryer you should replace it. Losing charge means a leak to atmosphere. The dryer will absorb every bit of moisture and non-condensable gas until it is saturated while at exposed to atmosphere. This will make your system run hot and inefficient even with a new compressor (it'll blow cold but you are seriously shortening the life span). Because you have already used OTC cans you have charged oil int the low side (thats where those POS things hook up) which means your system also is overladen with oil and most likely in the dryer too. So to get it up to snuff you'll have to replace the compressor, dryer, and have it properly evacuated/charged.

I'm a universal tech that has done units worth that would pay for 200 new ZR-1s

Formula413 08-13-2010 07:05 AM

So the proper procedure would be: Replace compressor and dryer, evacuate system, recharge. Correct? And I assume the evacuation and recharge pretty much needs to be done by a shop?

BrokenFeather78 08-13-2010 09:07 PM

Yes a shop will have to evac and charge. It's cheaper than having to go through it again prematurely

ILuvPizzaTimes10 08-14-2010 01:16 AM

Mehh vaccing it out is a good idea if you have catastrofic failure. I would just make sure you don't leave the system open for too long. Swap it all out make sure you fill the compressor with. Th e right amount of fluid and run it

BrokenFeather78 08-14-2010 02:18 AM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 27128)
Mehh vaccing it out is a good idea if you have catastrofic failure. I would just make sure you don't leave the system open for too long. Swap it all out make sure you fill the compressor with. Th e right amount of fluid and run it

Will it work ? Yes, but with a shorter life. Any air in the system is going to cause failure much earlier in the systems life.

ILuvPizzaTimes10 08-14-2010 03:46 AM

Debatable. I say why waiste the money. They warrantee a compressor as long as you buy a reciever dryer. New one will absorb all moister. I wouldn't worry about it man.

Formula413 08-14-2010 03:49 PM

Would it still be a good idea to have it recharged at a shop as opposed to buying the cans at the parts store?

BrokenFeather78 08-15-2010 01:38 AM

I would take it to a shop. They have a proper setup not a craptastic gauge that's reading lo side pressure.

Formula413 08-15-2010 06:05 AM

Step one of course is to see if I can turn up a working used compressor so I don't have to drop $235 on a brand new one.

ILuvPizzaTimes10 08-15-2010 12:48 PM

that is probably the worst idea you've had so far.

Formula413 08-15-2010 03:28 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 27202)
that is probably the worst idea you've had so far.

Can you add anything useful to that?

ILuvPizzaTimes10 08-15-2010 03:53 PM

how are you goin to be sure of the condition of a used compressor. is it going to fail in a week a month a year you cant tell. and by the time you know it 3 used ones later you could have had a new one installed. spend your money once.

Formula413 08-03-2011 08:43 PM

Update: This is turning into a serious PITA. I have put two different compressors on the car, both brand new (not reman), different brands, and they both had squeaking pulleys. The stock compressor makes no noise at all, and I had it back on the car in between these two, and no noise. Anyone have any thoughts on what could cause this? Serpentine belt is new. Both pulleys spun freely and made no noise off the car. This is getting aggravating and I really need to figure out a solution.

941LE 08-03-2011 09:23 PM

did you have dye put throw it to see any if there were any leaks?

frankzlt1 08-04-2011 01:14 AM

Did u check the tensioner pulley or idler pulley the sound could travel and make a different part sound bad sometimes

Formula413 08-04-2011 02:28 AM

Yeah the tensioner seems perfectly fine. If it was the tensioner I would think it would make the noise with the stock compressor on there as well, but it doesn't. Only the aftermarket compressors. Anyone got an LT1 tensioner laying around I could try just to rule it out?

Grovlet 08-04-2011 06:02 PM

Is there a way to shim/adjust the pulley on the new compressors? I know you can sometimes get just the clutch assembly itself, so I would think there's an adjustment to account for that.

Essentially I wonder if the new one's are not adjusted and the pulley is slightly out of line with where it needs to be, but original is of course properly adjusted?

ILuvPizzaTimes10 08-04-2011 06:07 PM

Or the aftermarket compressor has a slightly smaller diameter pully and you will need a smaller belt. Does i t sound like belt chirp or metal on clutch material noise?

Formula413 08-04-2011 06:24 PM

I didn't see any way of adjusting anything. As for the noise it just sounds like a squeaking pulley. It gets a lot quiter once the engine is warmed up.

ILuvPizzaTimes10 08-05-2011 08:50 PM

belt is probably too short because the pulley on the A/C is a bit smaller then it should be.

Formula413 08-05-2011 09:11 PM

1 Attachment(s)
If the pulley was smaller that would make the belt too long. Here's a pic of both, I could take measurements but they look pretty close.

ILuvPizzaTimes10 08-05-2011 10:50 PM

Looks smaller too me. It squiks wether you are using the ac or not? If so check. Belt length.

Formula413 08-05-2011 11:11 PM

Yeah like I said I haven't even charged the AC yet much less turned it on. I'll try putting the old serp belt back on just for the heck of it. You don't have a tensioner lying around do you?

ls6monte 08-06-2011 12:57 AM

I think the pulley is the same on both. It looks smaller because the clutch on the gm compressor is so much bigger.

fasta**z28 08-06-2011 12:58 AM

got a used one i took off the lt1 over the winter u want it free ? and a tensioner


All times are GMT. The time now is 06:18 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.