North East F-Body Association

North East F-Body Association (http://www.northeastf-bodyassn.com/index.php)
-   Fourth Generation (http://www.northeastf-bodyassn.com/forumdisplay.php?f=16)
-   -   For all the lt1 haters... (http://www.northeastf-bodyassn.com/showthread.php?t=3366)

bottledbird68 10-03-2011 03:39 AM

For all the lt1 haters...
 
It's always the opti!!!!!

http://i641.photobucket.com/albums/u...8/2b2fcf36.jpg

Pulled the water pump off on the Camaro so we could pull the cap off to take a look see and here's the view that greeted us.
Tried cleaning up the terminals but now I runs even worse so I guess I'm gonna order up the replacement msd cap and rotor this week, tear it all apart, and hope this time finally solves it.
I'm thinking it will cause we're just about to the point where we're thinking we may as well keep the car. As soon as we decide not to let it go I'm thinking it'll run mint lol.

KLAB 10-03-2011 03:51 AM

EW that sucks sorry to hear / see. How many miles on it wtf??

bottledbird68 10-03-2011 04:08 AM

Umm, we probably put maybe 10-12,000 miles on it plus whatever pizza put on while it was on his car. I never opened it up when we got it. I'm thinking though that in the torrential downpour that started the whole issue water somehow found its way in there.

Found a tiny bit of oil in it too so I'm thinking I'm going to pull an reseal the timing cover at the same time.
Then if that works I think I'm going to go kick the shit out of it at the track rental the 14th.

KLAB 10-03-2011 12:46 PM

My opti to timing cover seal was good. If oil is getting in it I'm betting the o-rings on the opti input shaft are bad replace those! Oil goes down the shaft and comes out on the sensor wheel.

KLAB 10-03-2011 12:46 PM

and I also caked it up with sealant around the whole thing when I re-assembled it haha.

ILuvPizzaTimes10 10-03-2011 01:21 PM

Quote:

Originally Posted by KLAB (Post 56471)
My opti to timing cover seal was good. If oil is getting in it I'm betting the o-rings on the opti input shaft are bad replace those! Oil goes down the shaft and comes out on the sensor wheel.


all those orings do is keep the opti centered. how many times do i have to tell you! oil that geting to these it always coming from either the intake front "chine" wall. or the oil pump drive shaft seals. and i put i think 1500 miles on that opti before i sold it to you! i bet it was the rain bad winter we had and letting it sit. only times ive had issues with optis is wen the car sits for a LONG time with out being started. Good Luck! and make sure the new cap you get fits YOUR Opti. yours is now different with the extra bolt up top.

bottledbird68 10-03-2011 01:42 PM

Yeah I'm guessing it got wet from the torrential downpour I drove it home in. That plus sitting. And yup, I'm gonna order the proper msd cap/rotor for the msd opti from summit.

ZFreie 10-03-2011 03:23 PM

Makes me wonder what mine looks like at 160k...I'm pretty sure its the original lol

KLAB 10-03-2011 03:48 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 56476)
all those orings do is keep the opti centered. how many times do i have to tell you! oil that geting to these it always coming from either the intake front "chine" wall. or the oil pump drive shaft seals....

hmm, I think my seals let oil by and down the shaft hole. It came out inside the opti and flung off the wheel.

KLAB 10-03-2011 03:48 PM

http://i3.photobucket.com/albums/y53.../optispark.jpg

ZFreie 10-03-2011 04:09 PM

Couple puddles I've hit on accident looked about like that lol

Formula413 10-03-2011 05:17 PM

The only thing that scares me about puddles is the air intake.

KB93z28 10-04-2011 12:29 AM

I know my opti has been replaced twice, at least thats what the original owner told me. And that sucks man! are the MSD opti's supposed to be better than factory ones?

Formula413 10-04-2011 12:45 AM

Yeah, they're supposed to be...

Motaboata 10-04-2011 01:21 AM

I have a cap and rotor to an opti u can have for 30 bucks BNIB just come get it...I live in RI

bottledbird68 10-04-2011 01:28 AM

Thank you but we already ordered the msd replacement one this morning. ;)

bottledbird68 10-07-2011 09:52 PM

Ok, got the cap and rotor swapped out, fired it up, bled the coolant, shut it off and started it back up a few times, then, took it for a test drive. Car ran mint! Pulled hard as ever. Revved perfectly throughout the entire rpm range.
Yee haa!

And then, packed the shop up. Decided to take the car home. Almost didn't want to to start. Cranked extra long before it fired. Finally fired and seemed ok. Until she wen to pull out onto rt 20. Stumbled, sputtered, and broke up for a few seconds before it kicked in and took off.
Drove it to my parents anyhow. Going down the road it seems ok. Very light throttle it sputter/stumbles a little bit but not undriveable. If you try and start off normally it falls on it's face before it kicks in and rockets off.
Pound on it while going or rev it and dump it it takes off just fine. If you rev it to start off like a 5.slow asshat it's ok but if you try and start off like a normal person it buck and kicks.
I give up! Fuck this car! Lol. Any ideas? Or, toss the right cash in my face and take it away. I'll let it go much cheaper than my asking price lol. I've had it :p

84ta406 10-07-2011 10:39 PM

Hey matt, if you want we can throw my scan tool on it and see whats going on. I can do OBD 1

bottledbird68 10-07-2011 10:41 PM

I just may take you up on that. What's your availability?
Either that or I'm just probably gonna throw a tps at it tomorrow :(

84ta406 10-07-2011 10:54 PM

I'm at my dads place tonight, and I believe tomorrow afternoon/night and sunday as well. He lives just off 122 on the worc. paxton line. Only like 10 mins from your parents house.

bottledbird68 10-07-2011 11:23 PM

Do you want me to head there or do you mind swinging by the shop?
Supposed to have someone coming by to pick up the six speed I have for sale around 11. We have family plans for Sunday, and we work tonight and tomorrow night. So yeah, I have tomorrow afternoon if you're bored lol.

My84Z 10-07-2011 11:57 PM

can almost bet your have something arching or a defective coil or something. especially if it was fine at first.

Formula413 10-08-2011 12:01 AM

Did I already ask what brand wires?

bottledbird68 10-08-2011 12:20 AM

No it's being temperature related still. After the car warms up it sucks ass.

Alex, did it with the Taylor wires that were on it and with the new automate wires we just put on. Also with the old plugs and the new ones we put in last week. :/

Formula413 10-08-2011 12:24 AM

Is there some way to force the car to stay in open loop and see if that changes anything?

bottledbird68 10-08-2011 12:48 AM

Yes there is. Unplugging the maf should force it into open loop and no, it doesn't change anything.
It's like everything decided to go all at once. F this car lol!

KB93z28 10-08-2011 01:00 AM

Have you tried replacing the coolant temp sensor in the water pump? This is all I can think of if you thinks its temp. related.

bottledbird68 10-08-2011 01:04 AM

Yup. Already did that

My84Z 10-08-2011 03:14 AM

How bout the one in the head? Try running the car in pitch black with the hood open and look for arching

Formula413 10-08-2011 03:18 AM

The sensor in the head is just for the temp gauge as far as I know. As for the MAF, if it's unplugged the car would run in speed density, but would it force open loop? I'm not sure on that. My car won't run at all with the MAF unplugged.

irockidz28 10-08-2011 04:36 AM

could possibly be a sticking valve???? i know its temp related but..anything is possible right...

bottledbird68 10-08-2011 04:44 AM

From what I read o2 sensors or maf force it into open loop. Runs exactly the same with or without the maf.

And John, it has the exact same issue with the old plugs/wires/cap as it does with the new ones we just installed so I doubt it's a wire issue :(

ILuvPizzaTimes10 10-08-2011 01:33 PM

Ignition Control Module. it will get to a point were it wont stay running, it will run Great warm up then die, it then wont start till the ICM cools off. i think i have a couple spares there rather expensive. so dont buy one if you dont want and wen i go home today ill dig mine out?

ZFreie 10-08-2011 01:53 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 56705)
Ignition Control Module. it will get to a point were it wont stay running, it will run Great warm up then die, it then wont start till the ICM cools off. i think i have a couple spares there rather expensive. so dont buy one if you dont want and wen i go home today ill dig mine out?

How about the icm spacer mod? Also, I would try going to a computer store and getting artic silver or some other kind of thermal paste and re attach the heat sink to the icm. IF the thermal paste is old and dry it wont do its job of transferring heat to the heat sink.

KLAB 10-08-2011 02:20 PM

dont space it is better touching the head :)

KLAB 10-08-2011 02:23 PM

it cools off faster being in contact with the head, plus touching the head allows it to only get as hot as the aluminum, being in open air with nothink to attempt thermal equilibrium with other than the air allows it to heat up hotter and take longer to cool off.

[/behaviorofmaterials]

ZFreie 10-08-2011 02:23 PM

Quote:

Originally Posted by KLAB (Post 56718)
dont space it is better touching the head :)

Yea? Mines still attached to the head, never had an issue with the icm, when i replaced the coil, i put new thermal past on and no issues.


Quote:

Originally Posted by KLAB (Post 56719)
it cools off faster being in contact with the head, plus touching the head allows it to only get as hot as the aluminum, being in open air with nothink to attempt thermal equilibrium with other than the air allows it to heat up hotter and take longer to cool off.

[/behaviorofmaterials]

It has its own heatsink....in theory while moving on or off the head should make little difference. sitting still or when you shut the car off is a different story.

ILuvPizzaTimes10 10-08-2011 02:31 PM

if the icm is heating up and then causing an issue. the fix isnt to take it off the head. the fix is to replace it. further more moving it off the head makes little difference. relocating it entirely to another location will. either way its STILL Bolted to the head. and heat transfer will occur regardless. So try that Matt. the lower rpm chug after its warm only makes sence that its the ICM if it was the optical sensor itself, it would break up at high rpm as well. Thats what ive found anyway. i have been wrong in the past. just trying to help.

ZFreie 10-08-2011 02:34 PM

Quote:

Originally Posted by ILuvPizzaTimes10 (Post 56721)
Thats what ive found anyway. i have been wrong in the past. just trying to help.

What he said lol

bottledbird68 10-08-2011 10:15 PM

Not the icm unless both of the ones I have here are causing the exact same issue. Already tried that too :(
Thank you though. Any other ideas?


All times are GMT. The time now is 12:34 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.