Go Back   North East F-Body Association > F-Body Garage > Fourth Generation
Reload this Page Rear Main Seal bolt snapped inside of block
Join Us-Register FAQ Calendar Search Today's Posts Mark Forums Read Arcade

Reply
Page 1 of 3 1 23
 
Thread Tools Display Modes
  #1  
Old 04-16-2011, 09:04 PM
black heartbeat black heartbeat is offline
Post Whore
  
Join Date: Oct 2009
Location: Mashpee, Cape Cod
Posts: 1,273
Post Thanks / Like
Thanks (Given): 4
Thanks (Received): 18
Likes (Given): 22
Likes (Received): 76
Dislikes (Given): 1
Dislikes (Received): 3
Default Rear Main Seal bolt snapped inside of block
so I was putting the rear main seal housing on today and long story short the bolt snapped under 15 ft lbs of torque...an inch into the block i can't seem to drill it out without it walking off the center if the bolt to even get an extractor in, its a 1/4 inch bolt and I need this thing out now any ideas?
__________________
Reply With Quote
  #2  
Old 04-16-2011, 09:43 PM
black heartbeat black heartbeat is offline
Post Whore
  
Join Date: Oct 2009
Location: Mashpee, Cape Cod
Posts: 1,273
Post Thanks / Like
Thanks (Given): 4
Thanks (Received): 18
Likes (Given): 22
Likes (Received): 76
Dislikes (Given): 1
Dislikes (Received): 3
Default
just in I just drilled through the center of the bolt
__________________
Reply With Quote
  #3  
Old 04-16-2011, 09:48 PM
frankzlt1's Avatar
frankzlt1 frankzlt1 is offline
Post Whore
  
Join Date: Jun 2010
Posts: 1,992
Post Thanks / Like
Thanks (Given): 2
Thanks (Received): 101
Likes (Given): 11
Likes (Received): 180
Dislikes (Given): 12
Dislikes (Received): 2
Default
That sucks I feel your pain. Were u able to get it out.
Reply With Quote
  #4  
Old 04-16-2011, 10:26 PM
KB93z28's Avatar
KB93z28 KB93z28 is offline
SLOWMARO
Chopper Challenge Champion 		 
Join Date: Dec 2010
Location: Whitinsville, MA
Posts: 1,189
Post Thanks / Like
Thanks (Given): 53
Thanks (Received): 24
Likes (Given): 97
Likes (Received): 136
Dislikes (Given): 7
Dislikes (Received): 10
Default
Just make sure you dont snap a screw extractor in the hole you drilled, then your really screwed.......theres no drilling those things lol
__________________
1993 BGGM Z28, stock LT1, T56, 175k on original motor, basic bolt-ons. 273 whp, 308wtq. SOLD
2001 Black WS6 TA Stock....for now....
DD: 2007 Dodge Ram 1500 quad cab sport, 6 inch RCX lift, 35x13.5 tires, 20x9 Fuel wheels, 20% tint all the way around, ZZ customs exhaust, Diablosport Trinity T1000 programmer.
Reply With Quote
  #5  
Old 04-16-2011, 10:38 PM
black heartbeat black heartbeat is offline
Post Whore
  
Join Date: Oct 2009
Location: Mashpee, Cape Cod
Posts: 1,273
Post Thanks / Like
Thanks (Given): 4
Thanks (Received): 18
Likes (Given): 22
Likes (Received): 76
Dislikes (Given): 1
Dislikes (Received): 3
Default
Quote:
Originally Posted by KB93z28 View Post
Just make sure you dont snap a screw extractor in the hole you drilled, then your really screwed.......theres no drilling those things lol
Just did
__________________
Reply With Quote
  #6  
Old 04-16-2011, 10:49 PM
KB93z28's Avatar
KB93z28 KB93z28 is offline
SLOWMARO
Chopper Challenge Champion 		 
Join Date: Dec 2010
Location: Whitinsville, MA
Posts: 1,189
Post Thanks / Like
Thanks (Given): 53
Thanks (Received): 24
Likes (Given): 97
Likes (Received): 136
Dislikes (Given): 7
Dislikes (Received): 10
Default
Quote:
Originally Posted by black heartbeat View Post
Just did
Uh-oh, thats no good lol....not sure what to do now....is it sticking out of the block a little? If you have a dremel, or anything like that, maybe try to cut a slot in the extractor so you can get a flat head screw driver on it, not sure how well that would work but....thats all I got
__________________
1993 BGGM Z28, stock LT1, T56, 175k on original motor, basic bolt-ons. 273 whp, 308wtq. SOLD
2001 Black WS6 TA Stock....for now....
DD: 2007 Dodge Ram 1500 quad cab sport, 6 inch RCX lift, 35x13.5 tires, 20x9 Fuel wheels, 20% tint all the way around, ZZ customs exhaust, Diablosport Trinity T1000 programmer.
Reply With Quote
  #7  
Old 04-16-2011, 10:53 PM
black heartbeat black heartbeat is offline
Post Whore
  
Join Date: Oct 2009
Location: Mashpee, Cape Cod
Posts: 1,273
Post Thanks / Like
Thanks (Given): 4
Thanks (Received): 18
Likes (Given): 22
Likes (Received): 76
Dislikes (Given): 1
Dislikes (Received): 3
Default
there about an inch before you get to the threading for the bolt so I'm thinking tap the the shouldered section with a fine thread I should be able to get away with this
__________________
Reply With Quote
  #8  
Old 04-16-2011, 11:42 PM
ls6monte's Avatar
ls6monte ls6monte is offline
Sticker Bitch
  
Join Date: Oct 2009
Location: Holbrook,Ma
Posts: 3,494
Post Thanks / Like
Thanks (Given): 0
Thanks (Received): 92
Likes (Given): 0
Likes (Received): 230
Dislikes (Given): 0
Dislikes (Received): 36
Default
Do you want to shoot Sully for this car or YOU for buying it????????????????????????? lol
__________________
Ron
85 Monte SS, 2004 Corvette LS6 w/02 T56, 9" rearend, 390/364 rwhp/tq ,Slowhawk tuned, 3575 lbs
11.74@114.6mph
BACK IN THE GAME!!
DD 06 Cobalt SS/sc, stock w/k+n only
14.78@97mph

http://www.cardomain.com/ride/2151623
http://www.racecarsbyhalls.com
http://www.slowhawkperformance.com

Another show Lady- Why does your car say Corvette on the engine? We have a Corvette and your car doesn't look like one. LMFAO
Reply With Quote
  #9  
Old 04-16-2011, 11:57 PM
black heartbeat black heartbeat is offline
Post Whore
  
Join Date: Oct 2009
Location: Mashpee, Cape Cod
Posts: 1,273
Post Thanks / Like
Thanks (Given): 4
Thanks (Received): 18
Likes (Given): 22
Likes (Received): 76
Dislikes (Given): 1
Dislikes (Received): 3
Default
No comment
__________________
Reply With Quote
  #10  
Old 04-17-2011, 01:10 PM
KB93z28's Avatar
KB93z28 KB93z28 is offline
SLOWMARO
Chopper Challenge Champion 		 
Join Date: Dec 2010
Location: Whitinsville, MA
Posts: 1,189
Post Thanks / Like
Thanks (Given): 53
Thanks (Received): 24
Likes (Given): 97
Likes (Received): 136
Dislikes (Given): 7
Dislikes (Received): 10
Default
How'd you make out?
__________________
1993 BGGM Z28, stock LT1, T56, 175k on original motor, basic bolt-ons. 273 whp, 308wtq. SOLD
2001 Black WS6 TA Stock....for now....
DD: 2007 Dodge Ram 1500 quad cab sport, 6 inch RCX lift, 35x13.5 tires, 20x9 Fuel wheels, 20% tint all the way around, ZZ customs exhaust, Diablosport Trinity T1000 programmer.
Reply With Quote
Reply
Page 1 of 3 1 23

« Previous Thread | Next Thread »
Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT. The time now is 07:40 PM.

Contact Us - North East F-Body Association - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.