|
#11
01-18-2010, 09:40 PM
|
||||
|
||||
Josh it makes no real difference what came stock. all you need to know if it fits into the yoke on the 9" or not. BUT stock 3rd gen from 1985 up i believe were all 1310's. my ford 9" from a bronco was also a 1310. i used a stock driveshaft. if that housing has a 1350 yoke on it, get a 1310/1350 ujoint and your done. a stock steel drive shaft will handle the load of what your doing. unless you spray it out of the hole or sumthing you'll be fine.
__________________
 1998 Firebird:buncha parts thats used to make it go fast..... not so much anymore.  BAAAAAA!!!!!! 
|
|
#12
01-18-2010, 09:55 PM
|
|||
|
|||
|
Thats the thing. I know the slip yoke for the trans is a 1350 and I know the rearend uses a 1350 but I dont know what the shaft uses so I can get the correct conversion U-joints.
__________________
5.3L LSx, Fbody .500 cam, TH400, 4500 Stall, Moser 9"
|
|
#13
01-18-2010, 10:04 PM
|
||||
|
||||
|
measure it and you will get the answer from my post. and like I said 1310 was the 4th gen also if I were you I would just get a new shaft with 1350 all around. my 1310/1350 u joint lasted 1/2 a track day on et streets. snapped it right in half
__________________
 2000 SS Procharger 98 Z vert turbo 07 TB SS cai catback and tune
|
|
#14
01-19-2010, 07:01 AM
|
||||
|
||||
|
^^^ thats cuz you break everything you touch. But josh hes right. if your going that route just spend the extra doe and get a shaft made up.
__________________
1998 Firebird:buncha parts thats used to make it go fast..... not so much anymore. BAAAAAA!!!!!!
|
|
#15
01-19-2010, 01:26 PM
|
|||
|
|||
|
The shaft I have is a 3.5" steel shaft, got it from a kid who used it for a th350 swap with a stock rear. It's just got the wrong slip yoke for me and the rear u-joints dont match. I want to use this one for now.
__________________
5.3L LSx, Fbody .500 cam, TH400, 4500 Stall, Moser 9"
|
|
#16
01-20-2010, 12:49 AM
|
||||
|
||||
|
bring it to a drive shaft shop. best one around is south shore bearing. have em conver that shaft if its not a 1350 shaft to a 1350 shaft. they can cut the yokes off and reweld new ones on and balance it. for usually under 200 bux.
__________________
1998 Firebird:buncha parts thats used to make it go fast..... not so much anymore. BAAAAAA!!!!!!
|
|
#17
01-20-2010, 12:59 AM
|
|||
|
|||
|
We've got a really good place around here. I'll call em from work and see if I get a discount.
__________________
5.3L LSx, Fbody .500 cam, TH400, 4500 Stall, Moser 9"
|
|
#18
01-20-2010, 01:15 AM
|
||||
|
||||
|
Quote:
__________________
 1986 Camaro Iroc z28 305 TPI 700R4 -hooker-edelbrock 1 5/8" shorty headers-1.6 roller rockers-52mm TB-3.23 10 bolt- ...191rwhp/280rwtq...14.97@90.5 2.04 60' 2005 GMC Sierra 2500 LLY Duramax -exhaust-gauges-leveled-wheels-tune-egr delete....339rwhp/637rwtq
|
|
#19
01-20-2010, 01:55 AM
|
||||
|
||||
|
Call em depending on whats wrong with it, it may be cheaper to get a used one sometimes.
__________________
1998 Firebird:buncha parts thats used to make it go fast..... not so much anymore. BAAAAAA!!!!!!
|
 |
|
|
Linear Mode
